Whirlpool WED5500XW0 Service Manual

The Whirlpool WED5500XW0 is a 4.3 cu. ft. capacity electric dryer with advanced moisture sensing, multiple dry cycles, and durable stainless steel drum. This service manual covers technical specifications, installation procedures, operational guidelines, troubleshooting, and maintenance information for qualified service technicians.

1. Technical Specifications 2. Installation Requirements 3. Control Panel Operation 4. Electrical Components 5. Mechanical Components 6. Diagnostic Mode 7. Error Codes 8. Disassembly Procedures 9. Testing Procedures 10. Parts List 11. Troubleshooting Guide

Technical Specifications

Key technical data for the Whirlpool WED5500XW0 electric dryer.

SpecificationDetails
Model NumberWED5500XW0
Capacity4.3 cubic feet
Power Requirements240V AC, 60Hz, 30A
Dryer TypeElectric
Drum MaterialStainless Steel
Dimensions (HxWxD)43.5" x 29" x 28.5"
Weight125 lbs
Moisture SensorYes
Cycle OptionsAuto Dry, Timed Dry, Air Fluff
Warranty1 year parts and labor

Installation Requirements

Proper installation procedures for the WED5500XW0 dryer.

  1. Location: Install on level surface with adequate ventilation.
  2. Electrical: Connect to dedicated 240V, 30A circuit with proper grounding.
  3. Venting: Use 4-inch diameter metal ducting, maximum 25 feet length.
  4. Gas line: Not applicable (electric model only).
  5. Leveling: Adjust leveling legs to ensure proper operation.

WARNING! Electrical installation must be performed by qualified technician. Ensure proper grounding to prevent electrical shock.

Control Panel Operation

Control panel functions and user interface operation.

Electrical Components

Major electrical components and their specifications.

ComponentPart NumberFunction
Heating ElementWPW10206370Provides heat for drying
Thermal FuseWPW1054170Safety cutoff for overheating
MotorWPW10727472Drives drum and blower
TimerWPW1054171Controls cycle timing
Start SwitchWPW10001625Initiates cycle operation
Door SwitchWPW10001070Detects door position

Mechanical Components

Key mechanical parts and assembly information.

Diagnostic Mode

Accessing and using the diagnostic mode for troubleshooting.

  1. Enter diagnostic mode: Press and hold "More Time" and "Less Time" buttons for 3 seconds
  2. Navigate tests: Use cycle selector knob to scroll through test options
  3. Run component tests: Select test and press Start to activate
  4. Exit diagnostic: Turn cycle selector to OFF position

CAUTION! Diagnostic mode should only be used by qualified service technicians.

Error Codes

Common error codes and their meanings.

Error CodeDescriptionPossible Cause
F01Thermal fuse openOverheating, restricted venting
F02Motor circuit faultMotor failure, wiring issue
F03Heating element faultElement failure, thermostat issue
F05Moisture sensor errorSensor failure, wiring problem
F07Control board failureMain board malfunction

Disassembly Procedures

Step-by-step disassembly instructions for service access.

  1. Unplug dryer from electrical outlet
  2. Remove top panel: Insert putty knife at rear corners and lift forward
  3. Remove front panel: Remove screws and disconnect door switch wires
  4. Access drum: Remove belt and lift drum out
  5. Remove heating element: Access through rear panel after drum removal

WARNING! Always disconnect power before disassembly. Document wire locations for reassembly.

Testing Procedures

Component testing methods and expected values.

Parts List

Common replacement parts and their part numbers.

Part DescriptionPart Number
Heating Element AssemblyWPW10206370
Drive BeltWPW10002563
Thermal FuseWPW1054170
Door SwitchWPW10001070
Idler PulleyWPW10001741
Lint FilterWPW10206372
Main Control BoardWPW1054173

Troubleshooting Guide

Common problems and their solutions.

SymptomPossible CauseCorrective Action
Dryer won't startPower, door switch, start switchCheck power supply, test door switch, verify start switch operation
No heatHeating element, thermal fuseTest heating element continuity, check thermal fuse
Drum not turningBelt, motor, idler pulleyInspect belt condition, test motor, check idler pulley
Long drying timesVenting, heating elementCheck venting for restrictions, test heating element
Error codes displayedVarious component failuresReference error code chart, perform diagnostic tests

Service Support: 1-800-253-1301; www.whirlpool.com/parts

Whirlpool WED5500XW0 Service Manual © - All Rights Reserved 2025