Whirlpool Gold Series Dishwasher Parts Manual

The Whirlpool Gold Series Dishwasher is a premium built-in dishwasher featuring advanced cleaning technology, multiple wash cycles, energy-efficient operation, stainless steel interior, quiet performance, and durable construction. This parts manual provides comprehensive information on replacement parts, installation guidelines, maintenance procedures, and troubleshooting for the Whirlpool Gold Series Dishwasher models. Below are key sections covering parts identification, installation, maintenance, and technical specifications.

Parts Identification

Key components: Control panel assembly, door latch mechanism, spray arms, filter system, heating element, pump assembly, water inlet valve, drain pump, and rack system.

Installation Guidelines

Proper installation ensures optimal performance and longevity.

1. Prepare opening: Ensure cabinet opening meets specified dimensions.
2. Connect water supply: Use 1/2-inch water line with shut-off valve.
3. Connect drain line: Install high-loop in drain hose to prevent backflow.
4. Electrical connection: Connect to dedicated 120V, 15-amp circuit.
5. Level dishwasher: Adjust leveling legs for proper door alignment.

WARNING! Disconnect power and water supply before installation. Follow local plumbing and electrical codes.

Maintenance Procedures

Regular maintenance ensures efficient operation and extends appliance life.

1. Clean filter monthly: Remove and rinse filter assembly under running water.
2. Inspect spray arms: Clear any clogged spray holes with toothpick.
3. Check door seal: Wipe clean and inspect for damage or wear.
4. Run cleaning cycle: Use dishwasher cleaner every 3-6 months.
5. Inspect racks: Check for rust or damage to rack coating.

CAUTION! Always disconnect power before performing maintenance. Use only manufacturer-approved cleaning products.

Technical Specifications

• Dimensions: Standard 24-inch width built-in design.
• Capacity: 14-16 place settings depending on model.
• Water Consumption: 2.5-4.5 gallons per cycle.
• Power Requirements: 120V AC, 60Hz, 15A dedicated circuit.
• Water Pressure: 20-120 psi required for proper operation.
• Noise Level: 44-50 dBA depending on model and cycle.
• Wash Cycles: Normal, Heavy, Light, Rinse Only, Sanitize.
• Drying System: Heated dry with optional air dry setting.
• Construction: Stainless steel tub and door interior.

Control Panel Components

Front control panel with electronic touch controls and LED display.

Main Components: Control board, display module, touchpad assembly, wiring harness, cycle selector switch.

Cycle Options: Normal Wash, Heavy Wash, Light Wash, Rinse Only, Sanitize, Delay Start, Heated Dry. Options: High Temp Wash, Sani Rinse, Steam Prewash. Display Indicators: Cycle progress, time remaining, clean/dry status, error codes.

Water System Parts

Complete water management system including inlet, circulation, and drainage.

1. Water Inlet Valve: Controls water flow into sump area.
2. Circulation Pump: Moves water through spray arms during wash cycles.
3. Drain Pump: Removes wastewater from dishwasher.
4. Spray Arms: Upper and lower arms with precision spray patterns.
5. Heating Element: Heats water for washing and air for drying.

Tip: Regularly check for leaks at connection points and ensure proper water temperature (120°F minimum).

Electrical Components

Electrical system ensuring safe and reliable operation.

1. Main Control Board: Microprocessor controlling all dishwasher functions.
2. Door Switch: Safety interlock preventing operation when door open.
3. Heating Element Thermostat: Prevents overheating during dry cycle.
4. Wash Motor: Drives circulation pump for water movement.
5. Drain Motor: Powers drain pump for water removal.
6. Wiring Harness: Connects all electrical components.

WARNING! Always disconnect power before servicing electrical components. Use multimeter to test components.

Door Assembly Parts

Complete door assembly including latch, seal, and inner panel.

1. Door Latch Assembly: Mechanical and electronic locking mechanism.
2. Door Gasket: Rubber seal preventing water leaks.
3. Inner Door Liner: Stainless steel interior surface.
4. Handle Assembly: Door opening and closing mechanism.
5. Door Springs: Assist with smooth door operation.
6. Hinge System: Upper and lower hinge points.

CAUTION! Door is heavy; support properly during service. Ensure proper alignment during reassembly.

Rack and Spray Arm Components

Dish loading system and water distribution components.

1. Upper Rack Assembly: Adjustable rack for glasses and cups.
2. Lower Rack Assembly: Heavy-duty rack for plates and bowls.
3. Utensil Basket: Removable basket for silverware.
4. Upper Spray Arm: Rotating arm for upper rack cleaning.
5. Lower Spray Arm: Primary rotating arm for lower rack.
6. Rack Rollers: Nylon wheels for smooth rack movement.
7. Rack Guides: Side tracks for rack alignment.

WARNING! Do not overload racks beyond capacity. Ensure spray arms rotate freely.

Troubleshooting Guide

Reset: Disconnect power for 5 minutes to reset control board.

Service: 1-800-253-1301; www.whirlpool.com/parts

Parts Ordering Information

Genuine Whirlpool replacement parts ensure optimal performance and safety.

1. Identify model number: Located on door edge or tub interior.
2. Contact authorized dealer: Use model number to order correct parts.
3. Online ordering: Visit www.whirlpoolparts.com for part lookup.
4. Warranty information: Most parts covered by limited warranty.
5. Installation: Professional installation recommended for complex components.

Note: Using non-genuine parts may void warranty and affect performance.