Whirlpool Gas Cooktop Installation Manual

The Whirlpool Gas Cooktop is a high-performance cooking appliance featuring sealed burners, electronic ignition, durable porcelain enamel grates, continuous grates for easy cookware movement, and easy-to-clean surfaces. This manual covers safety precautions, installation requirements, connection procedures, operation, maintenance, and troubleshooting for proper installation and use.

1. Safety Information 2. Installation Requirements 3. Installation Steps 4. Gas Connection 5. Specifications 6. Controls and Operation 7. Maintenance and Cleaning 8. Troubleshooting 9. Warranty Information

Safety Information

Important safety instructions to prevent fire, explosion, electric shock, and personal injury.

Warning Type	Precaution
Fire Hazard	Do not store flammable materials near cooktop
Gas Leak	Check all connections with soap solution after installation
Burn Prevention	Use proper cookware; keep handles turned inward
Ventilation	Ensure adequate ventilation during operation
Child Safety	Supervise children near cooking appliance

WARNING! If you smell gas, immediately shut off gas supply, open windows, and do not operate electrical switches.

Installation Requirements

Before installation, ensure you have the following requirements:

Countertop cutout dimensions: As specified in specifications section
Gas supply: Natural gas or LP gas with proper pressure regulator
Electrical outlet: 120V AC, 60Hz grounded outlet within reach of power cord
Clearance: Minimum 30 inches above cooktop to combustible materials
Ventilation: Range hood or overhead exhaust fan recommended

CAUTION! Installation must comply with local codes and ordinances.

Installation Steps

Follow these steps for proper cooktop installation:

Prepare countertop: Cut opening according to template dimensions
Apply sealant: Apply non-hardening sealant around cutout edge
Position cooktop: Carefully lower cooktop into opening
Secure mounting: Install mounting brackets according to instructions
Connect gas line: Use approved flexible gas connector
Connect electrical: Plug into grounded electrical outlet
Test operation: Check all burners for proper ignition and flame

WARNING! Cooktop is heavy; use two people for installation to prevent injury.

Gas Connection

Proper gas connection procedures for safe operation.

Shut off main gas supply before beginning installation
Use pipe joint compound or Teflon tape on all threaded connections
Connect flexible gas line to cooktop gas inlet
Check for leaks using soapy water solution - bubbles indicate leaks
Ensure gas pressure is within specified range (3.5" WC for natural gas)

IMPORTANT! Gas connection must be performed by qualified technician only.

Specifications

Burner Configuration: 4 or 5 sealed burners (varies by model)
Burner Output: Various BTU ratings (5,000 - 15,000 BTU)
Ignition System: Electronic spark ignition
Gas Type: Natural gas or convertible to LP gas
Gas Pressure: Natural gas: 3.5" WC; LP gas: 10" WC
Electrical: 120V AC, 60Hz, 15A circuit
Materials: Porcelain enamel grates, stainless steel or glass surface
Dimensions: Varies by model (typically 30-36 inches wide)

Controls and Operation

Control knobs located on front panel for easy access.

Burner Controls: Turn knob to LITE position for ignition, then adjust flame height. Infinite control valves allow precise temperature adjustment.

Ignition System: Automatic spark ignition - no standing pilot light. If ignition fails, wait 5 minutes for gas to dissipate before retrying.

Burner Caps: Ensure proper alignment for even flame distribution. Clean burner ports regularly to prevent clogging.

Maintenance and Cleaning

Regular maintenance ensures optimal performance and longevity.

Daily cleaning: Wipe surface with damp cloth and mild detergent
Burner cleaning: Remove grates and caps; clean with warm soapy water
Igniter cleaning: Use soft brush to clean spark igniter area
Grate cleaning: Wash porcelain enamel grates in warm soapy water
Spill management: Clean spills immediately to prevent staining

CAUTION! Do not use abrasive cleaners or steel wool on surfaces.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Burner won't light	No gas supply/clogged ports	Check gas valve; clean burner ports; ensure proper knob operation
Uneven flame	Clogged burner ports	Clean burner ports with soft brush; check cap alignment
Yellow flame	Improper air mixture	Adjust air shutter; ensure proper gas pressure
Igniter clicks but no flame	Gas supply issue	Check gas valve; wait 5 minutes and retry
Gas odor	Gas leak	Immediately shut off gas; check connections; call technician

Service: For technical assistance, contact Whirlpool at 1-800-253-1301

Warranty Information

Whirlpool Gas Cooktops come with limited warranty coverage:

Parts: 1-year limited warranty on all parts
Burners: 10-year limited warranty on sealed burners
Ignition System: 5-year limited warranty on electronic ignition
Labor: 90-day labor coverage from date of purchase